PSPIN100
MORE FOR PLUMBING
PSPIN100- Special for Plumbing

3-Pieces Set for plumbing applications, with "heavy-duty" pieces designed for the hard copper found in the plumbing field. HEX SHANKS!

       1/2''   3/4''        1''

PSPIN100 SWAGING SPIN TOOLS FOR PLUMBING

The PSPIN100 Swaging Set is ready to deliver the ideal depth for  the joints necessary in plumbing applications.

PRE HEATING MIGHT BE REQUIRED FOR TUBING ABOVE 7/8'', DUE WALL THICKNESS.

PLEASE WATCH THIS VIDEO TO GET THE BEST OUT YOUR SPIN PLUMBING SET.

 

*This SPIN Set is not available for sale  in all regions.

SSPIN500
MORE BASIC SET
SSPIN500- Basic Set

4-pieces set for perfect swages!

   1/4''     3/8''     1/2''   5/8''

s500

*This SPIN Set is not available for sale  in all regions.

SSPIN100
MORE STANDARD SET
SSPIN100- Standard Set

 

A 5-pieces Set aimed to the most common tubing diameters in AC units on the world.

1/4'' 3/8''  1/2''  5/8'' 3/4''

s100

*This SPIN Set is not available for sale  in all regions.

SSPIN300
MORE COMPLETE SET
SSPIN300- Complete Set

6-Pieces Set with the most common HVAC tubing diameters, and two "heavy-duty" pieces for larger tubes found in the field.

1/4''   3/8''   1/2''    5/8''   3/4''   7/8''

s300

The SSPIN300 Swaging Set contains the whole range of Swaging SPIN Tools. That's all you will need to make perfect swages in AC hard or soft copper tubing.

*This SPIN Set is not available for sale  in all regions.

SWAGING SPIN TOOLS

The high-temperature, leakage-free swaging method, designed from the ground up for HVAC systems.

Better Quality Expansions!
Less Joints!

The Swaging SPIN Tool is designed for the most common tubing diameters in HVAC, and it's recommended to both soft and hard copper. The high-temperature method preserves the copper’s/aluminum’s malleability while performing the swage, preventing cracks and leaks.

The Swaging Spin Tools allows you to connect tubes with ease and without the use of extra fittings; sleeves and unions, turning potential waste into actual profit.

To top that, you can swages with the Swage SPIN Tools in just 5 seconds!

To perform the swage on copper/aluminum tubing, simply attach the corresponding SPIN Tool size to a drill*. Because they perform their job using high-temperature and friction, no clamping tools or holders are necessary.

No more struggling with the swaging tool. The drill provides the strength, not your hands!

SPIN is the new evolution for HVAC swaging tools.

The 5-Second SwageAn Illustrated Guide Featuring How Effortless It Is To Use The SPIN Tools

Check for further information in the complete User's Manual or watch live How To Videos.

FASTEN IT!

FASTEN the Flaring SPIN Tool into the drill’s chuck. Ensure it’s on tight and FIRMLY hold the tube at all times. You can use your other hand if needed, but be sure to keep a safe distance from the tip of the tube.

LET'S GO IN...

Keep the drill at MAXIMUM SPEED, at all times. ALIGN the tube and drill. INSERT the Swaging SPIN. Maintain a CONSTANT PRESSURE through the process until the tool stopper has met with the tube.

... AND OUT!

Keep the tube and drill ALIGNED. Keep the drill at MAXIMUM SPEED. PULL OUT the Swaging SPIN from the tube. REMEMBER: this swaging process is an “in-and-out” sequel that is approximately 5 to 7 seconds.

THAT'S IT!

Immediately after, the tube’s temperature is very high. Don’t touch the swage until the tube has cooled off. FINAL RESULTS is an expansion with just the right depth and diameter to adjacent to the other tube.

DO THE COUPLING!

ASSEMBLE the fitting as usual. You might find it very easy to braze this fitting. The depth of the swage assures a tight and firm coupling. Counteracting long term stress fatigue of the material.

*Minimum Requirements

The Swage SPIN Tools are designed for copper tubing sizes of ¼ ”, ⅜” and ½” with wall thickness up to 0.8mm; & 1.0mm for a tubing diameter of ⅝”. Using the Swage Spin Tools on ANY other diameter than the recommended might cause undesirable deformation and assembling issues. Check User’s Manual for more details.

All SPIN Tools are designed to work with drills and/or screwdrivers, with a minimum of 1,800 RPM and 500 watts, for corded drills, or superior and 1,800RPM and 18V, or superior, for cordless drills. Using the SPIN Tools with a less powerful equipment tool than suggested, may result decreased and low-quality performances.

TOP